Пожалуйста, используйте этот идентификатор, чтобы цитировать или ссылаться на этот ресурс: http://elar.urfu.ru/handle/10995/82825
Полная запись метаданных
Поле DCЗначениеЯзык
dc.contributor.authorGrib, S. V.en
dc.contributor.authorIvasishin, O. M.en
dc.contributor.authorIllarionov, A. G.en
dc.contributor.authorKarabanalov, M. S.en
dc.date.accessioned2020-05-25T11:01:29Z-
dc.date.available2020-05-25T11:01:29Z-
dc.date.issued2019-
dc.identifier.citationRelationship Between the Texture and Young’s modulus over the Section of Cold-rolled Rods of Low-modulus Biocompatible Alloy / S. V. Grib, O. M. Ivasishin, A. G. Illarionov, M. S. Karabanalov // XIX International scientific-technical conference “The Ural school-seminar of metal scientists-young researchers” (Ekaterinburg, Russia, 19-23 December, 2018). – Dubai : Knowledge E, 2019. – KnE Engineering, 4 (1). – pp. 74-81. – DOI 10.18502/keg.v1i1.4393en
dc.identifier.issn2518-6841-
dc.identifier.urihttp://elar.urfu.ru/handle/10995/82825-
dc.description.abstractThe influence of the texture type on the Young's modulus value in the different sections of cold-deformed rods of Zr-31Ti-18Nb alloy (IMP BAZALM) was studied. It was found, an increase in the compression deformation degree from 63 to 84 % of Zr-31Ti-18Nb alloy during cold rolling contributed to the improvement of {001}<110> deformation cube texture. This contributed to the preferential orientation of the directions <001> and <110> parallel to ND and RD (TD) directions, accordingly. The minimum values of the Young's modulus were typical for areas where low-module <001> orientation prevailed, and the maximum values of the Young's modulus were characteristic for areas with high-modules <110> orientations. So, in the alloy deformed by 84 %, the lowest values of the Young's modulus were obtain in the rolling plane up to 53 GPa, and the highest values in plane perpendicular to the rolling direction up to 70 GPa.en
dc.description.sponsorshipThe study was funded by the grant of Russian Science Foundation (the project № 18-13-00220). The work was carried out using the laboratory equipment ”Structural methods of analysis and properties of materials and nanomaterials” of the Center of Ural Federal University.en
dc.format.mimetypeapplication/pdfen
dc.language.isoenen
dc.publisherKnowledge Een
dc.relationinfo:eu-repo/grantAgreement/RSF//18-13-00220en
dc.relation.ispartofXIX International scientific-technical conference “The Ural school-seminar of metal scientists-young researchers”. — Ekaterinburg, 2019en
dc.rightsCreative Commons Attribution Licenseen
dc.rights.urihttps://creativecommons.org/licenses/by/4.0/-
dc.subjectZR-TI-NB SYSTEMen
dc.subjectBIOCOMPATIBLE ALLOYen
dc.subjectYOUNG’S MODULUSen
dc.subjectTEXTUREen
dc.titleRelationship Between the Texture and Young’s modulus over the Section of Cold-rolled Rods of Low-modulus Biocompatible Alloyen
dc.typeConference Paperen
dc.typeinfo:eu-repo/semantics/conferenceObjecten
dc.typeinfo:eu-repo/semantics/publishedVersionen
dc.conference.nameXIX International scientific-technical conference “The Ural school-seminar of metal scientists-young researchers”en
dc.conference.date19.11.2018-23.11.2018-
dc.identifier.doi10.18502/keg.v1i1.4393-
local.description.firstpage74-
local.description.lastpage81-
local.fund.rsf18-13-00220-
Располагается в коллекциях:Конференции, семинары

Файлы этого ресурса:
Файл Описание РазмерФормат 
10.18502_keg.v1i1.4393.pdf3,12 MBAdobe PDFПросмотреть/Открыть


Лицензия на ресурс: Лицензия Creative Commons Creative Commons