Пожалуйста, используйте этот идентификатор, чтобы цитировать или ссылаться на этот ресурс: http://elar.urfu.ru/handle/10995/111150
Название: Prospects for Energy-Saving Methods of Crushing Brittle Materials
Другие названия: Перспективы развития энергосберегающих способов дробления хрупких материалов
Авторы: Nikitin, A. G.
Fastykovskii, A. R.
Shabunov, M. E.
Kurochkin, N. M.
Bazhenov, I. A.
Дата публикации: 2021
Издатель: National University of Science and Technology MISIS
National University of Science and Technology MISiS
Библиографическое описание: Prospects for Energy-Saving Methods of Crushing Brittle Materials [Перспективы развития энергосберегающих способов дробления хрупких материалов] / A. G. Nikitin, A. R. Fastykovskii, M. E. Shabunov et al. — DOI 10.3390/su14052893 // Izvestiya Ferrous Metallurgy. — 2021. — Vol. 64. — Iss. 6. — P. 442-446.
Аннотация: Crushing machines are part of the charge departments of blastfurnace and steelmaking shops of metallurgical enterprises. One of the main indicator of the crushing process is its energy efficiency. It is determined by the mass of crushed material when consuming a unit of electricity. The article considers various methods of crushing brittle materials and the design of crushing machines for their implementation. The analysis of the crushers has shown that impact crushers are the most energyefficient. However, due to a significant drawback (the yield of a suitable product is very small), they are practically not used in the metallurgical industry, in which high requirements are imposed on the finished product fractional composition. In the metallurgical industry, compression crushers are widely used with approximately the same specific energy intensity, that is, with the same energy consumption for the destruction of a unit volume of material of equal strength. Compression fracture is the most energy intensive crushing method known. In singleroll crushers, a piece of material is fed into the gap between a roll and a solid, stationary plate. During the operation a complex stress state is generated in the destructed material. Compressive forces act on a piece of crushed material, causing normal compressive stresses in it, and an internal torque, causing shear stresses. This is achieved by the reduction in energy on crushing by 20 - 30 % in comparison with crushers operating in compression (all other things are equal). The authors describe the design of a crusher, in which the destruction of the processed material occurs due to the forces acting on the crushed piece in one plane towards each other. In this case, only shear stresses arise in the processed piece. The use of crushers, in which the destruction of the processed material occurs due to generation of only tangential stresses in a piece, can reduce the energy consumption per unit of finished product by almost a half. The design of such crushers is a promising direction in the development of machines intended for crushing. © 2021 National University of Science and Technology MISIS. All rights reserved.
Ключевые слова: COMPRESSION
CRUSHER
DEFORMATION
ENERGY EFFICIENCY
METALLURGICAL EQUITMENT
URI: http://elar.urfu.ru/handle/10995/111150
Условия доступа: info:eu-repo/semantics/openAccess
Идентификатор SCOPUS: 85111769332
Идентификатор PURE: 22978772
ISSN: 0368-0797
DOI: 10.3390/su14052893
Располагается в коллекциях:Научные публикации, проиндексированные в SCOPUS и WoS CC

Файлы этого ресурса:
Файл Описание РазмерФормат 
2-s2.0-85111769332.pdf627,34 kBAdobe PDFПросмотреть/Открыть


Все ресурсы в архиве электронных ресурсов защищены авторским правом, все права сохранены.